Made to measure · printed in the USA

A drawer organizer that actually fits.

Measure your drawer, drag the dividers where you want them, and see it in 3D. We print your insert to fit wall to wall. No gaps, no sliding trays, no glue.

Instant priceFits to the millimeter183 colors, PETG & PLAPrinted in the USA
Plan view · 1:4 14 ⅝″ 11 ¼″ knives forks spoons ladles & tongs peelers wraps clips
MADE TO FITno gaps

How it works

Three steps. About five minutes.

Measure the inside

Width, depth and height of the drawer's inside, wall to wall. Our 2-minute guide shows where to put the tape.

Drag in the dividers

Start from a layout or a blank tray. Split, resize and merge compartments, then turn it in 3D to check every pocket.

We print it for you

Printed in the USA on our Bambu Lab H2S printers: one solid piece, or two that lock together for big drawers. Then checked, packed and shipped to your door.

Why made to fit

Loose trays slide. This doesn't.

  • Wall-to-wall fitSized to your drawer, less a small clearance so it drops in and lifts out.
  • No gaps, no rattlingThe walls and dividers are one solid part, nothing to shift when the drawer slams. Big drawers get two pieces that lock together with a hidden joint.
  • Scooped pocketsA rounded floor edge in every compartment, so paper clips and coins slide out with one finger.
  • Your layout, not oursAny number of compartments, any width. Lower the dividers for easy reach or keep them full height.
  • Names and labels, raised in the plastic"Screws," "Batteries," "Quarters," or your family name, printed right into the floor of any compartment.
  • Lids where you need themA drop-in lid with a finger notch for the screw bay or the change compartment. It sits flush with the dividers.
3D render of a drawer insert with four scooped compartments

Printed vs. bamboo

Why not just buy a bamboo tray?

Bamboo looks nice on the shelf. In a drawer, day after day, a printed insert made to your size simply works better.

DesignMyDrawer insert

  • Fits wall to wall. Made to your drawer's exact size, so nothing slides around.
  • Water and spills don't matter. Plastic doesn't swell, stain or grow mold. Wipe it or wash it.
  • Solid printed plastic. No glue joints to loosen, no splinters. Big drawers lock together with a hidden dovetail joint.
  • Your layout. Any number of compartments, any size, with labels and lids if you want them.
  • Made to last. Our standard PETG bends a little instead of snapping, and handles heat well. Pick Heavy duty walls for a solid feel.

Store-bought bamboo

  • Fixed sizes. Expandable trays leave gaps at the sides and back.
  • Glued strips of plant fiber. Damp spoons and spills can swell it, crack the glue joints, stain it or grow mold.
  • Joints and edges wear. Glue lets go and edges can splinter over the years.
  • Someone else's layout. You fit your things to the tray, not the other way around.
  • Thick walls. Sturdy, but they take up room you could use for storage.

Pricing

Priced by size. Shown before you pay.

The designer prices your exact insert from our slicer, the same software that runs the printers. Labels add $1 each, lids $2.50 each. Shipping and tax are added at checkout.

Small · bathroom, desk
$22.99from

About $27 for an 8 × 6″ insert with three compartments.

Medium · most drawers
$38– $45

Around 11 × 10″, five to eight compartments.

Large · per piece
$50– $58

Up to 13.1 × 12.4″ in one piece. Bigger drawers are made in two locking pieces.

183 colors · 19 finishes · PETG and PLA

Matte Soft, low-sheen finish that hides fingerprints.

White
Gray
Black

Special order: ships 3 to 5 days later.

Questions

Good to know.

How big can an insert be?

Up to 13.1 × 12.4 inches (335 × 315 mm) in one solid piece, and up to 4.7 inches (120 mm) tall. That's the build plate of the Bambu Lab H2S printers we use. Bigger drawers, like most kitchen drawers, are made in two pieces that lock together with a hidden dovetail joint inside one of the dividers. From above you only see a hairline.

What if my drawer has rounded corners or a lip?

Enter the corner radius in the designer and the insert's corners will match. If the drawer front has a lip or the slides stick in, measure the narrowest point. The measuring guide covers both.

What is it made of?

PETG Matte. It's tough, flexes a little instead of cracking, and the matte surface hides scratches and fingerprints.

How long does it take?

Most inserts print in 3 to 7 hours and ship within a few business days. The designer shows the ship date and delivery options for your ZIP code before you pay.

How do I clean it?

Lift it out and wash it with warm, soapy water. Skip the dishwasher's heated dry and very hot water, which can soften PETG.

All questions →

Your drawer, sorted.

Grab a tape measure. You'll see a 3D preview and a real price in a few minutes.

Start designing →